How to Remove Rust From Your Nissan Rogue

Unsightly rust spots can mar the beauty of a stunning vehicle, but by employing effective rust prevention methods, you can ensure your Nissan Rogue remains in pristine condition for the long term.

The key to mastering the art of preventing rust on a Nissan Rogue resides in your regular maintenance practices. It is far more efficient to prevent rust from developing initially than attempting to conceal corroded areas. Let's delve deeper into the world of rust prevention.

Go shopping for supplies

To begin, locate the paint code provided by the Nissan manufacturer. Note that this code can be found in various locations on the vehicle, such as the body, engine compartment, trunk, or other areas.

Next, acquire automotive touch-up paint in pints or quarts, suitable for use in a spray gun, aerosol cans, or roller ball applicators.

When dealing with automotive paint, even if you are proficient in using a spray gun, mixing the paint with a reducer to match the prevailing temperature and humidity conditions can be quite challenging.

We do not recommend this approach. Instead, opt for aerosol cans for more extensive repairs and utilize roller ball applicators for addressing scratches.

Please note that most modern vehicles have been painted with a base coat/clear coat system. The base coat contains only the pigment and binding resins, while the clear coat provides the glossy finish.

Be sure to purchase equal quantities of both the base coat and clear coat. Additionally, you will require an epoxy self-etching primer to adhere to bare metal and a lacquer primer to support the paint.

Finally, gather the following materials

40,600, and 1,000 grit sandpaper, a sanding block, grease and wax remover, poly sheeting, painter's tape, a tack rag, and a microfiber cloth.

Shop From Amazon

Chemical Guys ACC_326 – Torq Foam Blaster 6 Foam Wash Gun – The Ultimate Car Wash Foamer t...

Maxshine Snow Master Foam Cannon

AstroAI Foam Cannon, Heavy Duty Car Foam Blaster Wide Neck Adjustable Snow Foam Lance and...

Mask off the repair area

Position the poly sheeting a few feet in advance of the repair, securing it with tape. This will create ample space for seamlessly blending the touch-up paint into the undamaged areas.

Remove the rust

Utilize a scraper to remove any blistered paint. Employ 40 grit sandpaper to sand down to the bare metal, addressing the rust spots.

Expand the sanded area to allow room for feathering the edges. Transition to 120 grit sandpaper for the feathering process around the repair area.

Conclude the feathering by using 220 grit sandpaper. Employ a tack rag to eliminate any particles from the uncovered section.

Clean with detergent

If the rust has caused indentations in the metal, you have the option to fill them at this point using body filler. Alternatively, you can wait until the epoxy primer has fully dried and then apply multiple coats of filler primer. Here are some recommendations for selecting paint for rusted metal.

Thoroughly clean the entire exposed area using a grease-cutting dishwashing detergent, followed by a clean rinse with water.

Allow the surface to dry completely.

Use a lint-free cloth to wipe the area, ensuring any remaining dust or lint is removed. Apply the prep solvent recommended by the paint manufacturer.

Apply epoxy primer then filler primer

Apply the filler primer with slightly heavier coats, ensuring complete coverage over the entire repaired area. Gradually move the spray can away from the surface, blending it into the surrounding painted region.

Start with a self-etching epoxy primer for a robust bond to bare metal. It should be your initial coat. Spray two to three medium coats, adhering to the recommended waiting period specified on the label, typically around 15 minutes between each application.

Allow the epoxy primer to dry to the touch for a full hour, and longer if the weather is humid.

Sand the primer

Commence by using wet 600 grit sandpaper to gently smooth the primer while feathering the edges.

Transition to wet 1,000 grit sandpaper to perform the final sanding across the entire repair, encompassing the blended sections. Allow the surface to air dry after giving it a good rinse with clean water.

Once dry, use a lint-free cloth to clean the epoxy primer. Apply two to three somewhat thicker layers of lacquer filler primer, making sure to give each coat enough time to dry in between.

Before continuing, let the lacquer primer cure completely for at least an hour or until it is dry to the touch. Apply 320 grit sandpaper to any drips or sags, then continue with the final sanding of the whole restoration area.

Apply the colored base coat

Hold the spray can approximately 12 inches away from the surface, directing it towards the repaired region.

Start at the lowermost part of the repair and administer the color coat by moving in left-to-right rows, with each pass overlapping the previous one by about one third.

Gradually build up the color, applying it in two to three coats to seamlessly blend with the repair and its surrounding areas. Maintain a waiting period of approximately 10 to 15 minutes between each coat.

Allow the base coat to dry thoroughly, reaching a touch-dry state which typically takes at least 60 minutes. Avoid sanding the base coat, especially when dealing with metallic colors.

If you have encountered sags, lightly sand the affected areas and then reapply the necessary touch-up.

Spray on the clear coat

Apply multiple coats of clear coat, ensuring you adhere to the recommended drying time between each coat. Carefully blend the clear coat into the surrounding painted areas to achieve a seamless transition.

This step can be challenging because clear coats are prone to running, which can adversely affect your paint job's appearance. If you do encounter a run in the clear coat, allow it to dry for a minimum of 48 hours before attempting to rectify it using fine grit sandpaper and a polishing compound.

Afterward, you will need to reapply the clear coat to the sanded area. To gain proficiency in spraying, practice on a spare piece of cardboard to become familiar with the nozzle and application speed.

Allow the clear coat to dry for several hours before using the vehicle, and at a minimum, 48 hours before buffing.

Buff the repair

With the aid of an old cotton t-shirt or a microfiber cloth, manually buff the restored area using a buffing compound. Avoid using a polishing machine during this process. Wait for a minimum of 30 days before applying wax.